Curs Certified Data Center Specialist

Acest curs de instruire de cinci zile este dedicat sustinerii examenului Certified Data Center Specialist.

PRET DE LISTA
Contacteaza-ne
DURATA CURS
5 zile (40 ore)
CERTIFICARE CURS
Beingcert

Agenda cursului Certified Data Center Specialist

Module 1:

Lessons

  • Review of entire phases of Data Center Lifecycle
  • Planning, realigning and continual improvement

Module 2:

Lessons

  • Overview of rating level history
  • Differentiating between uptime and TIA‐942
  • Defining Rating level
  • Extra and unusable options (N + 1), 2N, 2 (N + 1)
  • Simultaneous Maintainability
  • Examples of configurations
  • Options for maintenance
  • Standards for operational procedures
  • Competence development

Module 3:

Lessons

  • Considering Building locations
  • Requirements for floor and hanging load
  • Walls and glass fire rating
  • Protection from any kind of forced entry
  • Blast protection
  • Bullet proofing of building

Module 4:

Lessons

  • Advanced level guidelines for installation of raised floor
  • Guidelines and techniques used for installation of raised access floor
  • Basic errors
  • Selecting the right tiles and their usage
  • Floor constructions that ease the seismic pressure
  • Selecting an appropriate suspended ceiling

Module 5:

Lessons

  • Advanced Power Infrastructure formulas required for a data center
  • Electrical diagrams of single line‐ efficiency in reading those and making sure about key components being available for protection
  • Protection from over current devices (like MCB, MCCB, VCB, ACB, Fuses) – their definitions and where to use what
  • Devices for preventing earth leakage (like RCB, RCD, ELCB, GFCI, ALCI, RCBO) – their definitions and where to use what
  • Numbering of protective components
  • Devices for preventing lightning strikes and surge protection (like TVSS/SPD) ‐ how to install those, their use and where to use
  • Considering Power cabling and cable run equipments
  • Set‐up and minimum requirements for PDU/DB

Module 6:

Lessons

  • Types of generators ‐ standy/prime/continuous
  • Elements make up and functions
  • Storage and calculation of fuel
  • Parallel use of gensets
  • Requirements for generator room and it’s area

Module 7:

Lessons

  • Active and Passive Harmonic filters and their usage

Module 8:

Lessons

  • Defining and designing of Battery Bank
  • Calculating and double checking of the battery bank being installed
  • Battery charging areas and making sure regarding the correct chargers being installed and used
  • Use of parallel battery banks, their limitations and risks when being used
  • Testing batteries accurately and deciding over cell/block or string replacement
  • Choosing between battery casing options: ABS, V0, V1, V2
  • Other energy storage options, flywheel, reusable cell, compressed air UPS etc.

Module 9:

Lessons

  • Electro‐Magnetic Fields, its sources and contrast between single phase, three phase and bus bar EMF
  • Convenient choices for evaluating EMF and ways to explicate results from single axes and composite measurements
  • Instructions on safe distance for humans and equipment
  • Evaluation of debilitation factor for protecting material permeability

Module 10:

Lessons

  • Definitions of essential topics – dry bulb, wet bulb, dew‐point, RH, sensible and latent heat
  • Effective cooling as per floor plan set up
  • Heat dissipation methods
  • ASHRAE recommendations and psychometric chart
  • Guidelines for temerature and humidity measurements
  • Altitude impact on temperature intake to ICT euipment
  • Air volume displacement calculations
  • Efficiency of air conditioning
  • Thermal units conversions
  • Rack door construction and floor performance impact
  • Evaluating cooling capacity
  • Efficiency indicator
  • Installation requirements
  • Authorization of air conditioners
  • De‐humidifying options
  • Delta‐T equipment and its impact
  • Optimizing airflow
  • Impact of SHR on cost saving
  • Calibration and setting points
  • Fire Panel and EPO connections
  • Computational Fluid Dynamics (CFD)

Module 11:

Lessons

  • The Fire triangle and the elements required to stop a fire that are part of Advanced Fire Protection
  • Detailed info about detection systems (VESDA, VIEW, smoke sensors)
  • Essentials to be considered before the installation of sensors
  • Appropriate testing of smoke sensors
  • Detecting the issues of water‐based systems like deluge, wet pipe, dry pipe, pre‐action etc.
  • Additional gas system requirements like release times, hold times, pipe install requirements, etc.
  • Evaluating the gas content that would ensure regarding the correct level of gas being installed to suppress the fire.
  • Fire detection panel requirements
  • Procedures involved in verifying the installation
  • Advanced Fire suppression techniques

Module 12:

Lessons

  • ANSI/TIA942 cabling structure topology
  • ToR/EoR Design
  • Intelligent patching systems
  • Best practices for installation such as routing, bending radius, separation from power,
  • containment fill ratio, fiber link loss calculator, bonding and grounding requirement
  • Administration, labeling and telecommunications standard
  • Brilliant patching system

Module 13:

Lessons

  • Acoustic noise effects, its specifications, limits and regulations
  • Contamination classifications at Data Center
  • Measurements, standards and limits
  • Measures for prevention and avoidance

Module 14:

Lessons

  • Green guidelines and standards for efficiency of Data Center
  • Ways to evaluate and checking for acceptable numbers compared to the general industry
  • PUE classification as defined by the Green Grid and problems with PUE
  • Various techniques for energy saving in the Data Center i.e. application/system level/ power distribution, cooling

Alte cursuri Beingcert de care ai putea fi interesat

Detinem in portofoliu mai mult de 25 tipuri diferite de cursuri Beingcert adresate companiilor (organizate la orice data si in orice locatie din tara)

Standard de calitate

Conform insusi principiului de baza al Sistemului de management al calitatii, implementat de IT Learning, obiectivul nostru este satisfactia clientului. Pentru atingerea acestui obiectiv, evaluarea calitatii serviciilor livrate este esentiala.

In acest sens va incurajam sa folositi orice cale si metoda de comunicare (feedback la cald si la rece, testimonial scris, telefon, e-mail, blog, forum, retele sociale etc.), pentru a va exprima, nu atat satisfactia pentru calitatea serviciilor noastre, care reprezinta in fapt angajamentul nostru ferm, asumat prin contract, cat mai ales, daca este cazul, insatisfactia de orice fel privind prestatia noastra, care ne va ajuta sa imbunatatim standardul acestor servicii, in beneficiul dvs.

Inscriere / Facturare / Plata / “Money back guarantee”

  • Daca sunteti persoana fizica, sau grup de maxim 5 participanti din partea unei companii, va puteti inscrie doar in clasele noastre deschise, anuntate pe site la pagina “Calendar Cursuri Open
  • Rezervarea locului / locurilor in sala de curs Open se face telefonic (0787.692.238) sau prin e-mail la adresa office@itlearning.ro , in reply urmand sa primiti fisa de inscriere care trebuie completata de dvs. si retrimisa noua impreuna cu datele de facturare
  • Urmeaza emiterea facturii, pe care o veti primi tot pe e-mail, in baza careia urmeaza sa efectuati plata (transfer bancar sau depunere numerar in contul IT Learning) si sa ne trimiteti confirmarea aferenta
  • Veti primi la randul dvs. confirmarea noastra ferma ca sunteti inscris(a) la cursul respectiv, impreuna cu detaliile organizatorice (orarul cursului, coffee-break, pauza de pranz etc.)
  • Urmeaza livrarea cursului, iar la finalul acestuia completarea feedback-ului, conform formularului de evaluare , in baza caruia se poate invoca clauza “Money back guarantee”: “In cazul obtinerii unui nivel de satisfactie mai mic de 75 % , reflectat de formularul de feedback, garantam returnarea taxei de participare sau reluarea cursului fara nici un cost”.
  • Daca sunteti persoana juridica si doriti inscrierea unui grup de peste 5 participanti, vom formula o oferta personalizata cu discount de volum, exclusiv pentru compania dvs., conform specificatiilor primite telefonic, prin fax (0371.602.780) sau pe e-mail la adresa office@itlearning.ro
  • Dupa acceptarea ofertei (livrabile, costuri, agenda, perioada si locatia organizarii cursului) urmeaza etapa contractuala
  • Odata agreata forma finala a contractului de legal-ul partilor, urmeaza semnarea si livrarea efectiva a serviciilor convenite, a caror facturare si plata se va face numai dupa primirea feadback-urilor completate de absolventi la finalul instruirii si numai in virtutea clauzei “Money back guarantee”:”In cazul obtinerii unui nivel de satisfactie mai mic de 75 % , reflectat de formularului atasat , garantam renuntarea la contravaloarea instruirii sau reluarea cursului cu alt trainer, fara nici un cost aditional”)

Inscrie-te la curs

Nume

Email

Despre mine

Tip mesaj

Mesaj